- Selection_004.jpg (127.17 KiB) Viewed 7076 times
It did finally come back so I will commence my testing.
First observation is that the time is correct on the log entries.
Firmware 1.2.0rc4 comments
-
lligetfa - Associate
- Posts: 1191
- Joined: Sun Aug 03, 2014 12:12 pm
- Location: Fort Frances Ont. Canada
- Has thanked: 307 times
- Been thanked: 381 times
Firmware 1.2.0rc4 comments
I just installed it and held my breath for a few minutes watching the progress bar go off the chart.
It did finally come back so I will commence my testing.
First observation is that the time is correct on the log entries.
It did finally come back so I will commence my testing.
First observation is that the time is correct on the log entries.
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: Firmware 1.2.0rc4 comments
Yea Eric needs to change that to a spinning wheel or something as I hate those periods as well.
Under the STP tab on WS-24-400A the Priority for ports 13-24 is grayed out and locked even if you enabled STP on that port. In my opinion we should allow all fields to be modified even if diabled but then we would have to do this on all Tabs like LAG.
I have yet to get the TFTP to work yet but might be doing it wrong so I will consult with the programmer.
Under the STP tab on WS-24-400A the Priority for ports 13-24 is grayed out and locked even if you enabled STP on that port. In my opinion we should allow all fields to be modified even if diabled but then we would have to do this on all Tabs like LAG.
I have yet to get the TFTP to work yet but might be doing it wrong so I will consult with the programmer.
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
- keefe007
- Experienced Member
- Posts: 169
- Joined: Tue Aug 05, 2014 3:56 pm
- Has thanked: 0 time
- Been thanked: 21 times
Duplicate VLANs
I noticed that the GUI allows one to create VLANs that already exist on the switch causing duplicate entries.
-
Hightech - Member
- Posts: 36
- Joined: Wed Mar 11, 2015 3:15 pm
- Has thanked: 3 times
- Been thanked: 5 times
Firmware 1.2.0rc4 update remote get switch unstable
We have the mgt on the switch on a tagget vlan1000 ip 10.0.0.10 gw 10.0.0.254/24 with ip and gateway.
If we firmware upgrade from a laptop on a routed net from 192.168.1.10 when the switch is updated now we see a higher ping responce with 3-5ms more then before and if we do a reboot remort from laptop the switch do not use gateway any more and only local access is working, to get it working again a new firmware upload is needed and only works to next remote reboot.....
some thing get wrong with the management Gateway stop working.....
We have tested this on 3 switches all with same resoult
/Carsten
If we firmware upgrade from a laptop on a routed net from 192.168.1.10 when the switch is updated now we see a higher ping responce with 3-5ms more then before and if we do a reboot remort from laptop the switch do not use gateway any more and only local access is working, to get it working again a new firmware upload is needed and only works to next remote reboot.....
some thing get wrong with the management Gateway stop working.....
We have tested this on 3 switches all with same resoult
/Carsten
-
Hightech - Member
- Posts: 36
- Joined: Wed Mar 11, 2015 3:15 pm
- Has thanked: 3 times
- Been thanked: 5 times
Re: Firmware 1.2.0rc4 update remote get switch unstable
We have now tested on a nother switch with firmware 1.1.0 with same resoult so it is a design error in both firmwares.......
We now have 4 broken switches.... We need some help!!!
/Carsten
We now have 4 broken switches.... We need some help!!!
/Carsten
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: Duplicate VLANs
keefe007 wrote:I noticed that the GUI allows one to create VLANs that already exist on the switch causing duplicate entries.
Nice catch, I will pass to programmers and we will fix this in v1.1.X and v1.2.X
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: Firmware 1.2.0rc4 update remote get switch unstable
Hightech wrote:We have the mgt on the switch on a tagget vlan1000 ip 10.0.0.10 gw 10.0.0.254/24 with ip and gateway.
If we firmware upgrade from a laptop on a routed net from 192.168.1.10 when the switch is updated now we see a higher ping responce with 3-5ms more then before and if we do a reboot remort from laptop the switch do not use gateway any more and only local access is working, to get it working again a new firmware upload is needed and only works to next remote reboot.....
some thing get wrong with the management Gateway stop working.....
We have tested this on 3 switches all with same resoult
/Carsten
Hightech wrote:We have now tested on a nother switch with firmware 1.1.0 with same resoult so it is a design error in both firmwares.......
We now have 4 broken switches.... We need some help!!!
/Carsten
If this broke the first switch WHY would you do it on 3 more switches?
v1.2.0rc4 is a RELEASE CANDIDATE and we says it is "untested"
You may need to downgrade to v1.1.0 and possibly factory default the switch and reset the switch up.
We put that firmware up there for people who want to test the firmware in a LAB or an environment that is not production!
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
lligetfa - Associate
- Posts: 1191
- Joined: Sun Aug 03, 2014 12:12 pm
- Location: Fort Frances Ont. Canada
- Has thanked: 307 times
- Been thanked: 381 times
Re: Firmware 1.2.0rc4 update remote get switch unstable
Hightech wrote:We have now tested on a nother switch with firmware 1.1.0 with same resoult so it is a design error in both firmwares.......
/Carsten
The switch with 1.1.0, was it downgraded from 1.2.0rc?
-
Hightech - Member
- Posts: 36
- Joined: Wed Mar 11, 2015 3:15 pm
- Has thanked: 3 times
- Been thanked: 5 times
Re: Firmware 1.2.0rc4 comments
no only upgraded to 1.1.0
we managed to get it workin again with this:
Default; manual konfiguration typing; updated firmware to 1.1.0; hard power off.
and then "reboot" from remote is working again
we will try to test this on 1.2.0rc4.......
we managed to get it workin again with this:
Default; manual konfiguration typing; updated firmware to 1.1.0; hard power off.
and then "reboot" from remote is working again
we will try to test this on 1.2.0rc4.......
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: Firmware 1.2.0rc4 comments
Hightech wrote:no only upgraded to 1.1.0
we managed to get it workin again with this:
Default; manual konfiguration typing; updated firmware to 1.1.0; hard power off.
and then "reboot" from remote is working again
we will try to test this on 1.2.0rc4.......
That is interesting, please report back! - THANKS
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Who is online
Users browsing this forum: No registered users and 18 guests