FIXES
- Fixed a serious issue with all v1.1.X and v1.2.0rcX firmware with the WS-8-250-AC model
- Fixed configuring PoE with CLI on ports 7/8 on WS-8-250-AC
- Fixed loop protection running on ports that are part of an aggregation
- Ensure ALL PoE is turned off before reboot when doing a factory reset
- Improved UI detecting when the device has rebooted
- Added warning message to VLAN secondary IP configuration
- Fixed STP sometimes running when disabled
KNOWN BUGS
- If using DHCP and you change the Default/Management VLAN ID after the switch gets an address is does not get a new address.
- LACP is half broken, if you use LACP configure it as you want it then reboot the switch and it comes up fine.
NOTE:
v1.1.X and v1.2.0rcX had bugs with the WS-8-250-AC ESPECIALLY v1.2.0rcX. - SORRY
If you are installing this version on a switch that has v1.2.0rcX, especially a WS-8-250-AC, and it acts weird still try power cycling it but if that does not help you may need to default the switch and re-set it up if after installing this version.
If you had never installed v1.2.0rcX then there should be no issues upgrading to v1.1.2
Released - 3/22/2015
Download latest Firmware
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
v1.1.2
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
v1.1.3
FIXES
- Fixed problem with the LACP/STP
- Send hostname with DHCP requests
KNOWN BUGS
- If using DHCP and you change the Default/Management VLAN ID after the switch gets an address is does not get a new address.
Released 3/23/2015
- Fixed problem with the LACP/STP
- Send hostname with DHCP requests
KNOWN BUGS
- If using DHCP and you change the Default/Management VLAN ID after the switch gets an address is does not get a new address.
Released 3/23/2015
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
v1.1.4
FIXES
- Fixes weird behavior of switch had you installed v1.2.0rc4 or v1.2.0rc5
- Fixes a long standing bug we had been chasing a while which manifested itself boldly in v1.2.0rcX but was also present in all previous version to a much lesser degree
KNOWN BUGS
- If using DHCP and you change the Default/Management VLAN ID after the switch gets an address is does not get a new address.
- Not all CLI commands are present.
- In the CLI some voltages are reported incorrectly with the "sh status" command
- In the CLI not all command are present to configure VLANs
Released 3/27/2015
- Fixes weird behavior of switch had you installed v1.2.0rc4 or v1.2.0rc5
- Fixes a long standing bug we had been chasing a while which manifested itself boldly in v1.2.0rcX but was also present in all previous version to a much lesser degree
KNOWN BUGS
- If using DHCP and you change the Default/Management VLAN ID after the switch gets an address is does not get a new address.
- Not all CLI commands are present.
- In the CLI some voltages are reported incorrectly with the "sh status" command
- In the CLI not all command are present to configure VLANs
Released 3/27/2015
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
v1.1.5
FIXES
- Fixed problem with Firefox and Safari introduced in 1.1.2 - YOU KNEW WE WOULD
- Fixed problem with password after upgrading from 1.0.10
....Unable to login to the UI or CLI after upgrade, required console cable to set new password
KNOWN BUGS
- If using DHCP and you change the Default/Management VLAN ID after the switch gets an address is does not get a new address.
- Not all CLI commands are present.
- In the CLI some voltages are reported incorrectly with the "sh status" command
- In the CLI not all command are present to configure VLANs
Released - 3/28-2015
- Fixed problem with Firefox and Safari introduced in 1.1.2 - YOU KNEW WE WOULD
- Fixed problem with password after upgrading from 1.0.10
....Unable to login to the UI or CLI after upgrade, required console cable to set new password
KNOWN BUGS
- If using DHCP and you change the Default/Management VLAN ID after the switch gets an address is does not get a new address.
- Not all CLI commands are present.
- In the CLI some voltages are reported incorrectly with the "sh status" command
- In the CLI not all command are present to configure VLANs
Released - 3/28-2015
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
v1.1.6
FIXES
- fixed problem changing password where you sometimes had to change the password TWICE sometimes for it to take.
****There are no other changes to v1.1.6 over v1.1.5
KNOWN BUGS
- If using DHCP and you change the Default/Management VLAN ID after the switch gets an address is does not get a new address.
- Not all CLI commands are present.
- In the CLI some voltages are reported incorrectly with the "sh status" command
- In the CLI not all command are present to configure VLANs
Released - 3/31/2015
- fixed problem changing password where you sometimes had to change the password TWICE sometimes for it to take.
****There are no other changes to v1.1.6 over v1.1.5
KNOWN BUGS
- If using DHCP and you change the Default/Management VLAN ID after the switch gets an address is does not get a new address.
- Not all CLI commands are present.
- In the CLI some voltages are reported incorrectly with the "sh status" command
- In the CLI not all command are present to configure VLANs
Released - 3/31/2015
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
v1.1.7
FIXES
- Fix where the mac used as the basis for the ipv6 local link address was not being properly set.
- Additional fixes for Firefox and Safari - Feel the love Firefox/Safari users
KNOWN BUGS
- If using DHCP and you change the Default/Management VLAN ID after the switch gets an address is does not get a new address.
- Not all CLI commands are present.
- In the CLI some voltages are reported incorrectly with the "sh status" command
- In the CLI not all command are present to configure VLANs
Released - 4/1/2015
- Fix where the mac used as the basis for the ipv6 local link address was not being properly set.
- Additional fixes for Firefox and Safari - Feel the love Firefox/Safari users
KNOWN BUGS
- If using DHCP and you change the Default/Management VLAN ID after the switch gets an address is does not get a new address.
- Not all CLI commands are present.
- In the CLI some voltages are reported incorrectly with the "sh status" command
- In the CLI not all command are present to configure VLANs
Released - 4/1/2015
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
v1.1.8
FIXES
- Fix an issue where a small number of UI/CLI reboots or firmware upgrade could resulted in the switch becoming inaccessible remotely.
- Fixes for Firefox and Safari - YES MORE FIXES
EXPLAINATION
When this occurred the switch would come up as expected continuing to power devices and pass traffic as configured but you could not ping the switch or log into the UI or CLI. This could be fixed by plugging your laptop into the switch which would wake up the Linux UI/CLI and or some people just rebooted the switch.
KNOWN BUGS
- STP Priority is being reported as 0 regardless of the setting
- If using DHCP and you change the Default/Management VLAN ID after the switch gets an address is does not get a new address.
- Not all CLI commands are present.
- In the CLI some voltages are reported incorrectly with the "sh status" command
- In the CLI not all command are present to configure VLANs
Released - 4/2/2015
- Fix an issue where a small number of UI/CLI reboots or firmware upgrade could resulted in the switch becoming inaccessible remotely.
- Fixes for Firefox and Safari - YES MORE FIXES
EXPLAINATION
When this occurred the switch would come up as expected continuing to power devices and pass traffic as configured but you could not ping the switch or log into the UI or CLI. This could be fixed by plugging your laptop into the switch which would wake up the Linux UI/CLI and or some people just rebooted the switch.
KNOWN BUGS
- STP Priority is being reported as 0 regardless of the setting
- If using DHCP and you change the Default/Management VLAN ID after the switch gets an address is does not get a new address.
- Not all CLI commands are present.
- In the CLI some voltages are reported incorrectly with the "sh status" command
- In the CLI not all command are present to configure VLANs
Released - 4/2/2015
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
v1.2.0rc6
FIXES
- Fixed scrolling on status page
- Fixed DHCP when changing the management VLAN ID
- Fixed SNMP stats for new models
- Fixed stats for new models in CLI
- Fixed problem with SFP ports not showing correct STP state on 12 port models
- Fixed problem configuring STP Priority
- Fixed MAC table sometimes showing filtered entries
- Ensure flashing 48VH PoE LED remains on during reboot
ENHANCEMENTS
- Added fallback to static IP configuration if DHCP fails
- Added DHCP Snooping
- Added Ubiquiti Discovery
- Added Cisco Discovery
- Added TFTP auto backup for config
- Added buttons to reorder VLANs
- Added support for WS-6-MINI, WS-8-250-DC, WS-12-250-AC and WS-12-250-DC
- Added Power tab for DC models
- Added current ratings to PoE settings in UI
- Added board rev to flash configuration
- Added CLI command to show vlans
- Added CLI command to change ID of VLANs
- Fixed scrolling on status page
- Fixed DHCP when changing the management VLAN ID
- Fixed SNMP stats for new models
- Fixed stats for new models in CLI
- Fixed problem with SFP ports not showing correct STP state on 12 port models
- Fixed problem configuring STP Priority
- Fixed MAC table sometimes showing filtered entries
- Ensure flashing 48VH PoE LED remains on during reboot
ENHANCEMENTS
- Added fallback to static IP configuration if DHCP fails
- Added DHCP Snooping
- Added Ubiquiti Discovery
- Added Cisco Discovery
- Added TFTP auto backup for config
- Added buttons to reorder VLANs
- Added support for WS-6-MINI, WS-8-250-DC, WS-12-250-AC and WS-12-250-DC
- Added Power tab for DC models
- Added current ratings to PoE settings in UI
- Added board rev to flash configuration
- Added CLI command to show vlans
- Added CLI command to change ID of VLANs
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
v1.2.0rc7
FIXES
- Fixed several cosmetic requests
ENHANCEMENTS
- Firmware up grader for DC power supply processor
KNOWN ISSUES
- Cable Diagnostic is broken
- Disabled ports shows lightening bolt instead of X
Released - 4/12/2015
- Fixed several cosmetic requests
ENHANCEMENTS
- Firmware up grader for DC power supply processor
KNOWN ISSUES
- Cable Diagnostic is broken
- Disabled ports shows lightening bolt instead of X
Released - 4/12/2015
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
sirhc - Employee
- Posts: 7415
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
v1.2.0rc8
FIXES
- Fixed cable diagnostics (prevent php sessions from timing out)
- Fixed current multiplier on WS-6-MINI (was reporting twice the actual current useage)
- Fixed lightning bolt showing on disabled ports which should have been an "X"
- Fixed copyright notice
KNOWN ISSUES
- DHCP is broken
Released - 4/15/2015
- Fixed cable diagnostics (prevent php sessions from timing out)
- Fixed current multiplier on WS-6-MINI (was reporting twice the actual current useage)
- Fixed lightning bolt showing on disabled ports which should have been an "X"
- Fixed copyright notice
KNOWN ISSUES
- DHCP is broken
Released - 4/15/2015
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Who is online
Users browsing this forum: No registered users and 15 guests