Netonix Forums

Please post comments and reports bugs with v1.3.8 FINAL in this thread

v1.3.8 wrote:FIXES
- Select all ports and add POE did not work correctly
- Port 1 Enables itself on reboot if disabled
- UI formatting Bugs
- Changed PoE Smart to now only check for "cross-shorts"
- Change voltage calculations to use 1 decimal point of precision
- Fan failure detection changes
- Better I2C error handling, primarily helps DC switches but better for all
- Fixes for DC switches Power Tab conditions

ENHANCEMENTS
- Add configurable config save timeout

KNOWN ISSUES
- Ubiquiti Discovery Protocol Still Broken
- large flat networks MAC table requiring too much CPU time
- IPERF is still a work in progress

Released 11/20/2015

Just got 1.3.7 installed on a few switches recently...will get 1.3.8 installed and report back in a few days

Installed 1.3.8 on a WS-24 and a WS-6 with no issues.

Thanks Eric, Dave, and Chris.

1.3.8 running on a few switches, both DC/AC including with SFPs in use.

Only having problems with SNMP not responding at times. Running snmpwalk will timeout when this happens. Eventually it will start to respond again. Weird issue.

Nothing sticks out on 'top' when ssh'd into the device.

New switch , never used, after installing new firmware 1.3.8, getting a 3 volt out of range, at 2.7 volts

Hi tcknudson,

This is not a software bug, it is hardware issue.

Obviously the Voltage Divider Resistor is either bad or the manufacturer of the resistor had an incorrect unit with the wrong value on the tape reel (this happens every so often with small components) and the wrong resistor got stuffed which throws off the calculation to determine the voltage. If the v3.3V was actually 2.7V it would not boot.

The resistor manufacturer tests the little tiny things to be within such and such tolerance but every now and then a bad one slips through and gets put on a reel with 10,000 good units.

Now a resistor can go bad especially from a small surge or something but since this is new out of the box I would bet the incorrect value resistor was stuffed.

Now the real question is why one of the 3 people who test the unit before it gets serialize did not catch it?

There are only 3 people who test the switches, Eric, Steph and myself so one of us missed it?

This is another reason we went to the meter graphs and warnings so anytime the switch see something out of range the software makes it very apparent to the user so it did it's job here as intended.

With the old software people did not pay attention to a bunch of numbers on the UI but they do pay attention to anything RED!

The unit is otherwise fine as obviously 2.7V is an incorrect reading or it would not be running but we can RMA that and replace the resistor.

Sorry for the issue and thanks for reporting.

v1.3.8 installed on WS-12-250-DC no problem , SNMP works correctly.
Like v1.3.8

Nacho Pla.
Moltelecom

Just upgraded my WS6 to 1.3.8. Everything looks great so far, if I don't post back then you guys are doing a great job!
The only thing I noticed was that the Rocket plugged into port 6 did a power cycle on upgrade, but ports 3, 4, and 5 did not. No big deal, but just interesting.

reighbread wrote:Just upgraded my WS6 to 1.3.8. Everything looks great so far, if I don't post back then you guys are doing a great job!
The only thing I noticed was that the Rocket plugged into port 6 did a power cycle on upgrade, but ports 3, 4, and 5 did not. No big deal, but just interesting.

What does the switch log say about port 6?

Upgraded to this version with no issue.
Not entirely digging the new UI though, e.g. with a quick glance I tot my fan was at 10000rpm until I saw the "coloured" meter.