Hello, we have a problem with a switch that goes down for around 20 minutes and then everything come back. We had this problem on the field and this morning, I had the switch in my lab and I did got the same problem. The problem appear after being up for around 20 minutes. Here's the console output :
Dec 31 19:21:15 system: starting ntpclient
+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU General Public License. You are welcome to change it and/or distribute
copies of it under certain conditions. Under the license terms, RedBoot's
source code and full license terms must have been made available to you.
Redboot comes with ABSOLUTELY NO WARRANTY.
Platform: VCore-III (MIPS32 24KEc) LUTON26
RAM: 0x80000000-0x88000000 [0x80021b68-0x87fafffc available]
FLASH: 0x40000000-0x40ffffff, 64 x 0x40000 blocks
== Executing boot script in 1.000 seconds - enter ^C to abort
+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU General Public License. You are welcome to change it and/or distribute
copies of it under certain conditions. Under the license terms, RedBoot's
source code and full license terms must have been made available to you.
Redboot comes with ABSOLUTELY NO WARRANTY.
Platform: VCore-III (MIPS32 24KEc) LUTON26
RAM: 0x80000000-0x88000000 [0x80021b68-0x87fafffc available]
FLASH: 0x40000000-0x40ffffff, 64 x 0x40000 blocks
== Executing boot script in 1.000 seconds - enter ^C to abort
+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU General Public License. You are welcome to change it and/or distribute
copies of it under certain conditions. Under the license terms, RedBoot's
source code and full license terms must have been made available to you.
Redboot comes with ABSOLUTELY NO WARRANTY.
Platform: VCore-III (MIPS32 24KEc) LUTON26
RAM: 0x80000000-0x88000000 [0x80021b68-0x87fafffc available]
FLASH: 0x40000000-0x40ffffff, 64 x 0x40000 blocks
== Executing boot script in 1.000 seconds - enter ^C to abort
RedBoot> fis load -d linux
Image loaded from 0x80100000-0x8036422c
RedBoot> go
Linux version 2.6.26.8 (dev@netonixdev) (gcc version 4.1.2) #2 Sun Sep 4 20:55:16 EDT 2016
Invalid kernel arglist - use RedBoot "exec" command to boot kernel.
Using predefined kernel options.
CPU revision is: 02019654 (MIPS 24K)
Determined physical RAM map:
User-defined physical RAM map:
memory: 08000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0 -> 32768
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyS0,115200 init=/etc/preinit mem=128M
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=8000d810
Readback ErrCtl register=8000d810
Cache parity protection enabled
PID hash table entries: 512 (order: 9, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126052k/131072k available (1917k kernel code, 4840k reserved, 417k data, 116k init, 0k highmem)
SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
net_namespace: 640 bytes
NET: Registered protocol family 16
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc.
msgmni has been set to 246
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x70100000 (irq = 14) is a 16550A
console [ttyS0] enabled
No NAND device found!!!
m25p80 spi0.0: m25p128 (16384 Kbytes)
Mapped SPI read area @0x40000000 len 16777216
Creating 10 MTD partitions on "m25p80":
0x00000000-0x00040000 : "RedBoot"
0x00040000-0x00080000 : "config"
0x00080000-0x001c0000 : "linux_recovery"
0x001c0000-0x003c0000 : "rootfs_recovery"
0x003c0000-0x00500000 : "linux"
0x00500000-0x00b00000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
0x00b00000-0x00f40000 : "rootfs_data"
0x00f40000-0x00f80000 : "FIS directory"
0x00f80000-0x00f81000 : "RedBoot config"
0x00fc0000-0x01000000 : "Redundant FIS"
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 116k freed
Please be patient, while OpenWrt loads ...
Algorithmics/MIPS FPU Emulator v1.5
- preinit -
Press CTRL-C for failsafe
Press and HOLD default button now for reset to factory defaults
mounting jffs2
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
- init -
Please press Enter to activate this console. Dec 31 19:00:04 syslogd started: BusyBox v1.19.4
Dec 31 19:00:04 kernel: klogd started: BusyBox v1.19.4 (2016-10-03 19:26:31 EDT)
Dec 31 19:00:04 kernel: Linux version 2.6.26.8 (dev@netonixdev) (gcc version 4.1.2) #2 Sun Sep 4 20:55:16 EDT 2016
Dec 31 19:00:04 kernel: Invalid kernel arglist - use RedBoot "exec" command to boot kernel.
Dec 31 19:00:04 kernel: Using predefined kernel options.
Dec 31 19:00:04 kernel: CPU revision is: 02019654 (MIPS 24K)
Dec 31 19:00:04 kernel: Determined physical RAM map:
Dec 31 19:00:04 kernel: User-defined physical RAM map:
Dec 31 19:00:04 kernel: memory: 08000000 @ 00000000 (usable)
Dec 31 19:00:04 kernel: Entering add_active_range(0, 0, 32768) 0 entries of 256 used
Dec 31 19:00:04 kernel: Zone PFN ranges:
Dec 31 19:00:04 kernel: Normal 0 -> 32768
Dec 31 19:00:04 kernel: Movable zone start PFN for each node
Dec 31 19:00:04 kernel: early_node_map[1] active PFN ranges
Dec 31 19:00:04 kernel: 0: 0 -> 32768
Dec 31 19:00:04 kernel: On node 0 totalpages: 32768
Dec 31 19:00:04 kernel: Normal zone: 256 pages used for memmap
Dec 31 19:00:04 kernel: Normal zone: 0 pages reserved
Dec 31 19:00:04 kernel: Normal zone: 32512 pages, LIFO batch:7
Dec 31 19:00:04 kernel: Movable zone: 0 pages used for memmap
Dec 31 19:00:04 kernel: Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Dec 31 19:00:04 kernel: Kernel command line: console=ttyS0,115200 init=/etc/preinit mem=128M
Dec 31 19:00:04 kernel: Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Dec 31 19:00:04 kernel: Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Dec 31 19:00:04 kernel: Writing ErrCtl register=8000d810
Dec 31 19:00:04 kernel: Readback ErrCtl register=8000d810
Dec 31 19:00:04 kernel: Cache parity protection enabled
Dec 31 19:00:04 kernel: PID hash table entries: 512 (order: 9, 2048 bytes)
Dec 31 19:00:04 kernel: Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Dec 31 19:00:04 kernel: Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Dec 31 19:00:04 kernel: Memory: 126052k/131072k available (1917k kernel code, 4840k reserved, 417k data, 116k init, 0k highmem)
Dec 31 19:00:04 kernel: SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Dec 31 19:00:04 kernel: Calibrating delay loop... 277.70 BogoMIPS (lpj=1388544)
Dec 31 19:00:04 kernel: Mount-cache hash table entries: 512
Dec 31 19:00:04 kernel: net_namespace: 640 bytes
Dec 31 19:00:04 kernel: NET: Registered protocol family 16
Dec 31 19:00:04 kernel: NET: Registered protocol family 2
Dec 31 19:00:04 kernel: Switched to high resolution mode on CPU 0
Dec 31 19:00:04 kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Dec 31 19:00:04 kernel: TCP established hash table entries: 4096 (order: 3, 32768 bytes)
Dec 31 19:00:04 kernel: TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
Dec 31 19:00:04 kernel: TCP: Hash tables configured (established 4096 bind 4096)
Dec 31 19:00:04 kernel: TCP reno registered
Dec 31 19:00:04 kernel: NET: Registered protocol family 1
Dec 31 19:00:04 kernel: squashfs: version 3.0 (2006/03/15) Phillip Lougher
Dec 31 19:00:04 kernel: Registering mini_fo version $Id$
Dec 31 19:00:04 kernel: JFFS2 version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc.
Dec 31 19:00:04 kernel: msgmni has been set to 246
Dec 31 19:00:04 kernel: io scheduler noop registered
Dec 31 19:00:04 kernel: io scheduler deadline registered (default)
Dec 31 19:00:04 kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
Dec 31 19:00:04 kernel: serial8250.0: ttyS0 at MMIO 0x70100000 (irq = 14) is a 16550A
Dec 31 19:00:04 kernel: console [ttyS0] enabled
Dec 31 19:00:04 kernel: No NAND device found!!!
Dec 31 19:00:04 kernel: m25p80 spi0.0: m25p128 (16384 Kbytes)
Dec 31 19:00:04 kernel: Mapped SPI read area @0x40000000 len 16777216
Dec 31 19:00:04 kernel: Creating 10 MTD partitions on "m25p80":
Dec 31 19:00:04 kernel: 0x00000000-0x00040000 : "RedBoot"
Dec 31 19:00:04 kernel: 0x00040000-0x00080000 : "config"
Dec 31 19:00:04 kernel: 0x00080000-0x001c0000 : "linux_recovery"
Dec 31 19:00:04 kernel: 0x001c0000-0x003c0000 : "rootfs_recovery"
Dec 31 19:00:04 kernel: 0x003c0000-0x00500000 : "linux"
Dec 31 19:00:04 kernel: 0x00500000-0x00b00000 : "rootfs"
Dec 31 19:00:04 kernel: mtd: partition "rootfs" set to be root filesystem
Dec 31 19:00:04 kernel: 0x00b00000-0x00f40000 : "rootfs_data"
Dec 31 19:00:04 kernel: 0x00f40000-0x00f80000 : "FIS directory"
Dec 31 19:00:04 kernel: 0x00f80000-0x00f81000 : "RedBoot config"
Dec 31 19:00:04 kernel: 0x00fc0000-0x01000000 : "Redundant FIS"
Dec 31 19:00:04 kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Dec 31 19:00:04 kernel: TCP cubic registeredDec 31 19:00:04 vtss_core: module license '(c) Vitesse Semiconductor Inc.' taints kernel.
switch: 'Luton26' board detected
nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
i2c /dev entries driver
i2c_vcoreiii i2c_vcoreiii: i2c bus driver on IRQ 19
vtss_cmn_qce_del:893 qce_id: 1 not found
+M25PXX : Init device with JEDEC ID 0x202018.
+M25PXX : Init device with JEDEC ID 0x202018.
+M25PXX : Init device with JEDEC ID 0x202018.
+M25PXX : Init device with JEDEC ID 0x202018.
+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU General Public License. You are welcome to change it and/or distribute
copies of it under certain conditions. Under the license terms, RedBoot's
source code and full license terms must have been made available to you.
Redboot comes with ABSOLUTELY NO WARRANTY.
Platform: VCore-III (MIPS32 24KEc) LUTON26
RAM: 0x80000000-0x88000000 [0x80021b68-0x87fafffc available]
FLASH: 0x40000000-0x40ffffff, 64 x 0x40000 blocks
== Executing boot script in 1.000 seconds - enter ^C to abort
+M25PXX : Init device with JEDEC ID 0x202018.
+M25PXX : Init device with JEDEC ID 0x202018.
+M25PXX : Init device with JEDEC ID 0x202018.
+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected�+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_�+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non�+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyrig�+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan�+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 200�+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, �+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foun�+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, �+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
Re�+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 200�+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free sof�+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU Ge�+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU General Public License. You are welcome to change it and/or distribute
copies of it under certain conditions. Under the license terms, RedBoot's
source code and full license terms must have been made available to you.
Redboot comes with ABSOLUTELY NO WARRANTY.
Platform: VCore-III (MIPS32 24KEc) LUTON26
RAM: 0x80000000-0x88000000 [0x80021b68-0x87fafffc available]
FLASH: 0x40000000-0x40ffffff, 64 x 0x40000 blocks
== Executing boot script in 1.000 seconds - enter ^C to abort
+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU General Public License. You are welcome to change it and/or distribute
copies of it under certain conditions. Under the license terms, RedBoot's
source code and full license terms must have been made available to you.
Redboot comes with ABSOLUTELY NO WARRANTY.
Platform: VCore-III (MIPS32 24KEc) LUTON26
RAM: 0x80000000-0x88000000 [0x80021b68-0x87fafffc available]
FLASH: 0x40000000-0x40ffffff, 64 x 0x40000 blocks
and so on... Until it reboot and stay up.
Is there anything to do or it's a RMA case ?
Thank you
Reboot problem with a WS-12-250AC
- QuebecInternet
- Member
- Posts: 21
- Joined: Wed Oct 05, 2016 4:55 pm
- Has thanked: 1 time
- Been thanked: 0 time
- QuebecInternet
- Member
- Posts: 21
- Joined: Wed Oct 05, 2016 4:55 pm
- Has thanked: 1 time
- Been thanked: 0 time
Re: Reboot problem with a WS-12-250AC
This switch has been on the field for around 6 hours before this problem started.
It was a brand new one.
It was a brand new one.
- QuebecInternet
- Member
- Posts: 21
- Joined: Wed Oct 05, 2016 4:55 pm
- Has thanked: 1 time
- Been thanked: 0 time
Re: Reboot problem with a WS-12-250AC
I did more test in the lab and the switch never came back after it started to reset. If I remove the power for 10 seconds, the switch start it boot process and in the middle, it start to reset. If I let it cool down, it take more time before it start resetting.
The temperature here in the field are around 4 Celsius.
It's definitively a hardware problem. I will ask for RMA
The temperature here in the field are around 4 Celsius.
It's definitively a hardware problem. I will ask for RMA
- QuebecInternet
- Member
- Posts: 21
- Joined: Wed Oct 05, 2016 4:55 pm
- Has thanked: 1 time
- Been thanked: 0 time
Re: Reboot problem with a WS-12-250AC
I just pull out a WS-12-250AC from the box this morning and I configured the basic to have it accessible. One radio powered (Nanostation 5M) and one cable for management. After 2h30 runtime, the switch rebooted by itself. Again, after 2 minutes (just the time to have access to the web interface), the radio rebooted again. 5 minutes later, rebooted again. For both switch, the firmware is 1.4.5.
Here's the console output (pretty the same as I had with the same switch.
show status give :
System
------
Current Time: 12/31/1969 19:07:28
Uptime: 448.779999 seconds
CPU Usage: 26%
Memory Usage: 40.95 MB
MAC Address: ec:13:b2:61:ce:8e
IP Address: 10.11.156.56
IPv6 Address: fe80::ee13:b2ff:fe61:ce8e
Firmware Version: 1.4.5
Model: WS-12-250-AC
Board Rev: F
Power
-----
Board 48V: 49.8 V
Board 24V: 24.7 V
Board 3V: 3.3 V
Thermal
-------
Board Temp: 37 C
CPU Temp: 55 C
PHY Temp: 55 C
Cooling
-------
Fan 1 Speed: 0 RPM
This is the reboot.
Switch Netonix 12 port# +M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU General Public License. You are welcome to change it and/or distribute
copies of it under certain conditions. Under the license terms, RedBoot's
source code and full license terms must have been made available to you�+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU General Public License. You are welcome to change it and/or distribute
copies of it under certain conditions. Under the license terms, RedBoot's
source code and full license terms must have been made available to you.
Redboot comes with ABSOLUTELY NO WARRANTY.
Platform: VCore-III (MIPS32 24KEc) LUTON26
RAM: 0x80000000-0x88000000 [0x80021b68-0x87fafffc available]
FLASH: 0x40000000-0x40ffffff, 64 x 0x40000 blocks
== Executing boot script in 1.000 seconds - enter ^C to abort
+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU General Public License. You are welcome to change it and/or distribute
copies of it under certain conditions. Under the license terms, RedBoot's
source code and full license terms must have been made available to you.
Redboot comes with ABSOLUTELY NO WARRANTY.
Platform: VCore-III (MIPS32 24KEc) LUTON26
RAM: 0x80000000-0x88000000 [0x80021b68-0x87fafffc available]
FLASH: 0x40000000-0x40ffffff, 64 x 0x40000 blocks
== Executing boot script in 1.000 seconds - enter ^C to abort
+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU General Public License. You are welcome to change it and/or distribute
copies of it under certain conditions. Under the license terms, RedBoot's
source code and full license terms must have been made available to you.
Redboot comes with ABSOLUTELY NO WARRANTY.
Platform: VCore-III (MIPS32 24KEc) LUTON26
RAM: 0x80000000-0x88000000 [0x80021b68-0x87fafffc available]
FLASH: 0x40000000-0x40ffffff, 64 x 0x40000 blocks
== Executing boot script in 1.000 seconds - enter ^C to abort
RedBoot> fis load -d linux
Image loaded from 0x80100000-0x8036422c
RedBoot> go
Linux version 2.6.26.8 (dev@netonixdev) (gcc version 4.1.2) #2 Sun Sep 4 20:55:16 EDT 2016
Invalid kernel arglist - use RedBoot "exec" command to boot kernel.
Using predefined kernel options.
CPU revision is: 02019654 (MIPS 24K)
Determined physical RAM map:
User-defined physical RAM map:
memory: 08000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0 -> 32768
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyS0,115200 init=/etc/preinit mem=128M
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=80049498
Readback ErrCtl register=80049498
Cache parity protection enabled
PID hash table entries: 512 (order: 9, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126052k/131072k available (1917k kernel code, 4840k reserved, 417k data, 116k init, 0k highmem)
SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
net_namespace: 640 bytes
NET: Registered protocol family 16
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc.
msgmni has been set to 246
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x70100000 (irq = 14) is a 16550A
console [ttyS0] enabled
No NAND device found!!!
m25p80 spi0.0: m25p128 (16384 Kbytes)
Mapped SPI read area @0x40000000 len 16777216
Creating 10 MTD partitions on "m25p80":
0x00000000-0x00040000 : "RedBoot"
0x00040000-0x00080000 : "config"
0x00080000-0x001c0000 : "linux_recovery"
0x001c0000-0x003c0000 : "rootfs_recovery"
0x003c0000-0x00500000 : "linux"
0x00500000-0x00b00000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
0x00b00000-0x00f40000 : "rootfs_data"
0x00f40000-0x00f80000 : "FIS directory"
0x00f80000-0x00f81000 : "RedBoot config"
0x00fc0000-0x01000000 : "Redundant FIS"
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 116k freed
Please be patient, while OpenWrt loads ...
Algorithmics/MIPS FPU Emulator v1.5
- preinit -
Press CTRL-C for failsafe
Press and HOLD default button now for reset to factory defaults
mounting jffs2
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
- init -
Please press Enter to activate this console. Dec 31 19:00:04 syslogd started: BusyBox v1.19.4
Dec 31 19:00:04 kernel: klogd started: BusyBox v1.19.4 (2016-10-03 19:26:31 EDT)
Dec 31 19:00:04 kernel: Linux version 2.6.26.8 (dev@netonixdev) (gcc version 4.1.2) #2 Sun Sep 4 20:55:16 EDT 2016
Here's the console output (pretty the same as I had with the same switch.
show status give :
System
------
Current Time: 12/31/1969 19:07:28
Uptime: 448.779999 seconds
CPU Usage: 26%
Memory Usage: 40.95 MB
MAC Address: ec:13:b2:61:ce:8e
IP Address: 10.11.156.56
IPv6 Address: fe80::ee13:b2ff:fe61:ce8e
Firmware Version: 1.4.5
Model: WS-12-250-AC
Board Rev: F
Power
-----
Board 48V: 49.8 V
Board 24V: 24.7 V
Board 3V: 3.3 V
Thermal
-------
Board Temp: 37 C
CPU Temp: 55 C
PHY Temp: 55 C
Cooling
-------
Fan 1 Speed: 0 RPM
This is the reboot.
Switch Netonix 12 port# +M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU General Public License. You are welcome to change it and/or distribute
copies of it under certain conditions. Under the license terms, RedBoot's
source code and full license terms must have been made available to you�+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU General Public License. You are welcome to change it and/or distribute
copies of it under certain conditions. Under the license terms, RedBoot's
source code and full license terms must have been made available to you.
Redboot comes with ABSOLUTELY NO WARRANTY.
Platform: VCore-III (MIPS32 24KEc) LUTON26
RAM: 0x80000000-0x88000000 [0x80021b68-0x87fafffc available]
FLASH: 0x40000000-0x40ffffff, 64 x 0x40000 blocks
== Executing boot script in 1.000 seconds - enter ^C to abort
+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU General Public License. You are welcome to change it and/or distribute
copies of it under certain conditions. Under the license terms, RedBoot's
source code and full license terms must have been made available to you.
Redboot comes with ABSOLUTELY NO WARRANTY.
Platform: VCore-III (MIPS32 24KEc) LUTON26
RAM: 0x80000000-0x88000000 [0x80021b68-0x87fafffc available]
FLASH: 0x40000000-0x40ffffff, 64 x 0x40000 blocks
== Executing boot script in 1.000 seconds - enter ^C to abort
+M25PXX : Init device with JEDEC ID 0x202018.
Luton26 board detected (VSC7425 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_18-Vitesse - built 05:56:33, Jan 31 2014
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU General Public License. You are welcome to change it and/or distribute
copies of it under certain conditions. Under the license terms, RedBoot's
source code and full license terms must have been made available to you.
Redboot comes with ABSOLUTELY NO WARRANTY.
Platform: VCore-III (MIPS32 24KEc) LUTON26
RAM: 0x80000000-0x88000000 [0x80021b68-0x87fafffc available]
FLASH: 0x40000000-0x40ffffff, 64 x 0x40000 blocks
== Executing boot script in 1.000 seconds - enter ^C to abort
RedBoot> fis load -d linux
Image loaded from 0x80100000-0x8036422c
RedBoot> go
Linux version 2.6.26.8 (dev@netonixdev) (gcc version 4.1.2) #2 Sun Sep 4 20:55:16 EDT 2016
Invalid kernel arglist - use RedBoot "exec" command to boot kernel.
Using predefined kernel options.
CPU revision is: 02019654 (MIPS 24K)
Determined physical RAM map:
User-defined physical RAM map:
memory: 08000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0 -> 32768
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyS0,115200 init=/etc/preinit mem=128M
Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=80049498
Readback ErrCtl register=80049498
Cache parity protection enabled
PID hash table entries: 512 (order: 9, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126052k/131072k available (1917k kernel code, 4840k reserved, 417k data, 116k init, 0k highmem)
SLUB: Genslabs=6, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Mount-cache hash table entries: 512
net_namespace: 640 bytes
NET: Registered protocol family 16
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc.
msgmni has been set to 246
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x70100000 (irq = 14) is a 16550A
console [ttyS0] enabled
No NAND device found!!!
m25p80 spi0.0: m25p128 (16384 Kbytes)
Mapped SPI read area @0x40000000 len 16777216
Creating 10 MTD partitions on "m25p80":
0x00000000-0x00040000 : "RedBoot"
0x00040000-0x00080000 : "config"
0x00080000-0x001c0000 : "linux_recovery"
0x001c0000-0x003c0000 : "rootfs_recovery"
0x003c0000-0x00500000 : "linux"
0x00500000-0x00b00000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
0x00b00000-0x00f40000 : "rootfs_data"
0x00f40000-0x00f80000 : "FIS directory"
0x00f80000-0x00f81000 : "RedBoot config"
0x00fc0000-0x01000000 : "Redundant FIS"
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 116k freed
Please be patient, while OpenWrt loads ...
Algorithmics/MIPS FPU Emulator v1.5
- preinit -
Press CTRL-C for failsafe
Press and HOLD default button now for reset to factory defaults
mounting jffs2
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
- init -
Please press Enter to activate this console. Dec 31 19:00:04 syslogd started: BusyBox v1.19.4
Dec 31 19:00:04 kernel: klogd started: BusyBox v1.19.4 (2016-10-03 19:26:31 EDT)
Dec 31 19:00:04 kernel: Linux version 2.6.26.8 (dev@netonixdev) (gcc version 4.1.2) #2 Sun Sep 4 20:55:16 EDT 2016
- QuebecInternet
- Member
- Posts: 21
- Joined: Wed Oct 05, 2016 4:55 pm
- Has thanked: 1 time
- Been thanked: 0 time
Re: Reboot problem with a WS-12-250AC
2 switch out of 2 with the same problem is a little odd.
I did try to reset to factory default using the little push button and the switch booted ok (without any POE activated). I suspected a PoE problem so I tried to downgrade the firmware to a release I know it work with our 8 ports but unfortunately, the switch rebooted in the middle of the upgrade process and it's now corrupted.
I did try to reset to factory default using the little push button and the switch booted ok (without any POE activated). I suspected a PoE problem so I tried to downgrade the firmware to a release I know it work with our 8 ports but unfortunately, the switch rebooted in the middle of the upgrade process and it's now corrupted.
- QuebecInternet
- Member
- Posts: 21
- Joined: Wed Oct 05, 2016 4:55 pm
- Has thanked: 1 time
- Been thanked: 0 time
Re: Reboot problem with a WS-12-250AC
Strangely, when doing the console recovery procedure, the fan was turning full speed and the switch didn't rebooted at all...
-
sirhc - Employee
- Posts: 7416
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: Reboot problem with a WS-12-250AC
QuebecInternet wrote:Strangely, when doing the console recovery procedure, the fan was turning full speed and the switch didn't rebooted at all...
The fan will always be at full speed until the firmware loads as the firmware controls the fan and by default the fan is on full speed.
We have seen a few defective 250 watts power supplies (I think we are up to 10+/- so far) that after a period of time reboot.
They may run fine for several hours or even as much as 12 hours then they start rebooting at random intervals. Turning them off for awhile they seem to work fine again and then after some period of time (several hours) they will start rebooting again.
This is why we are not catching them when we test them as we do not let every switch run for 12 hours, simply not possible to test for this type of issue.
Please RMA them and make sure you say on the description they reboot after a period of time, suspected power supply issue.
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
- QuebecInternet
- Member
- Posts: 21
- Joined: Wed Oct 05, 2016 4:55 pm
- Has thanked: 1 time
- Been thanked: 0 time
Re: Reboot problem with a WS-12-250AC
Thank you.
Could it be a production lot that is in problem ? Because we bought 2 of them and both have the problem
Could it be a production lot that is in problem ? Because we bought 2 of them and both have the problem
-
sirhc - Employee
- Posts: 7416
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: Reboot problem with a WS-12-250AC
QuebecInternet wrote:Thank you.
Could it be a production lot that is in problem ? Because we bought 2 of them and both have the problem
Well so far only found 10+/- defective powers supplies have been found out of a 2,000 batch
I am sure there are more out there yet to be found
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
- QuebecInternet
- Member
- Posts: 21
- Joined: Wed Oct 05, 2016 4:55 pm
- Has thanked: 1 time
- Been thanked: 0 time
Re: Reboot problem with a WS-12-250AC
Ok. So we will have to setup a test bench on our side to test for this because we had to drive 4 hours and climb a mountain to change the switch. If you can test this on your side, it will be part of having a better product that we can rely on.
Who is online
Users browsing this forum: No registered users and 41 guests