v1.4.7rcX Bug Reports and Comments

[Eric Stern]

One QoS question:

If a frame arrives to switch with vlan 54 and 802.1p PCP value 7 in a port with this vlan allowed and must go out for another port with this vlan allowed too,

Is PCP changed in any way during this travel?

No.

[TomO]

I'm looking at using the Double Tagged option, on 1.4.7rc14. I currently have tagged and untagged traffic on an interface that I am double tagging (or, I guess, single tagging in the case of the untagged traffic). It appears that I can still select the "T" option on other VLANs on this interface. Is this an oversight, or does this mean that I can have traffic traversing the interface on a specific VLAN that will not get double tagged?

FYI, currently I have two subinterfaces on a Cisco ASR1001x, one looking for the double tagged frames and one looking for the single tagged frames. This part is all working fine.

[Julian]

Your firmware could use an upgrade, try rc16?

[IntL-Daniel]

Does anyone noticed my last message on previous page?

I have noticed one borring feature or bug ? - when I change the name of some port which is used in watchdog table, the name is not changed there as well. I have to manually edit watchdog rule port number to other and back and click save (last seen in RC14).

[Eric Stern]

Yes, its on my to-do list.

[giannici]

Noticed an annoying bug in last RCs: is not more possible to deselect a port (a row in the list of ports) clicking again over the port row or over no port. Only a new port can be selected but not no port. You have to force a reload of the page to have no port selected again.

I don't know exactly when it happens, tested some conditions:

WS-12-DC e WS-8-150-DC with firmware 1.4.7rc11: works OK
WS-12-DC e WS-8-150-DC with firmware 1.4.7rc14 or 1.4.7rc16: Bug present!

[IntL-Daniel]

Noticed an annoying bug in last RCs: is not more possible to deselect a port (a row in the list of ports) clicking again over the port row or over no port. Only a new port can be selected but not no port. You have to force a reload of the page to have no port selected again.

I don't know exactly when it happens, tested some conditions:

WS-12-DC e WS-8-150-DC with firmware 1.4.7rc11: works OK
WS-12-DC e WS-8-150-DC with firmware 1.4.7rc14 or 1.4.7rc16: Bug present!

Already discussed above...

[giannici]

Noticed an annoying bug in last RCs: is not more possible to deselect a port (a row in the list of ports) clicking again over the port row or over no port. Only a new port can be selected but not no port. You have to force a reload of the page to have no port selected again.

I don't know exactly when it happens, tested some conditions:

WS-12-DC e WS-8-150-DC with firmware 1.4.7rc11: works OK
WS-12-DC e WS-8-150-DC with firmware 1.4.7rc14 or 1.4.7rc16: Bug present!

Already discussed above...

Oops!
Anyway, I used to "deselect" a port simply clicking in the "white" area below the list of port (before the graphs). I found it intuitive. Why don't keep it?
Thanks.

[giannici]

I have just found some strange behavior in a WS-12-DC with 1.4.7rc16.

Just after a reload of the entire page I found this in the STP tab:



Where are all other ports? And what is that "CIST" menu?

Then I simply click on some other tab and then return to the STP tab and the "CIST" row simply disappeared:



But all other ports are still missing!

Here it is the STATUS tab:

[lligetfa]

Noticed an annoying bug in last RCs: is not more possible to deselect a port (a row in the list of ports) clicking again over the port row or over no port.

No bug. Clicking outside of the white space on the left or right border deselects.