v1.4.7rcX Bug Reports and Comments

[Eric Stern]

A small bug crept into rc17, I'll release rc18 to fix it.

[IntL-Daniel]

Why we are o RCs instead of betas?

[sirhc]

Why we are o RCs instead of betas?

Because this is what we started with as far as release numbers.

I am sanity testing rc18 and will push it out here in the next hour or so.

[lligetfa]

Why we are o RCs instead of betas?

The betas are kept private.

[sirhc]

- Fixed STP tab on 12 port models - RC18

NOTE: MSTP is still being tested so use MSTP at your own risk.

FIXED/CHANGED
- Fixed temp sensors showing crazy values in very cold environments - RC3
- Fixed getting "unexpected link change" messages due to port bounce, watchdogs, etc - RC3
- Fixed port bounce being 1 hour off after daylight savings time changes - RC3
- Fixed VLAN tab layout getting messed up when you delete a VLAN - RC3
- Fixed mac table refresh button causing entire page to reload - RC3
- Fixed problem with QinQ when using untagged VLANs - RC3
- Fixed fan control handling negative temperatures - RC4
- Fixed input voltage graph labels - RC4
- Fixed Apply/Save becoming active when looking at MSTP configuration even though nothing changed - RC6
- Fixed port number in log messages - RC6
- Fixed issue when importing config from a RevE board to a RevF with different POE port options. Affected WS-6 and WS-12 - RC6
- Fixed the support for WS-8-150-AC - RC7
- Fixed console login
- Fixed/Force powerdown/powerup limits on WS-8-150-DC to help prevent switch lock up when draining battery to 9V - RC8
- Fixed DC2DC-500 detection for WS-26-500-DC - RC8
- Fixed voltage range on dumb DC models - RC8
- Fixed QinQ - RC9
- Fixed VLAN trunking - RC9
- Fixed Access Controls not honouring the Enable setting - RC11
- Fixed switch rebooting if multiple ports lose link too quickly - RC14
- Fixed multiple ports not turning off at the same time when they have the same shutdown voltage - RC14
- Fixed unexpected link change speed message - RC14
- Fixed port selection Tabs - RC14
- Fixed slight glitch in Input Current graph - RC16
- Fixed STP tab on 12 port models - RC18
- Allow QinQ and Double Tagging to be used with Trunk ports - RC9
- Changed UI layout on QOS tab - RC3
- Changed dumb DC models to temporarily disable POE when input voltage falls too low instead of disabling POE in the configuration - RC3
- Changed valid DC input voltage range to 9-72V in GUI for newer board revs - RC3
- Changed valid upper range for dc output voltage from 51V to 53V - RC3
- Changed input voltage graph to auto-scale - RC3
- Changed fan control to also use CPU and PHY temp - RC6
- Changed valid temp range on Status page meters - RC6
- Changed input voltage threshold where it forgets the configured Wake up voltage and defaults to 10V Wake up on WS-12-250-DC - RC10

ENHANCEMENTS
- Added MSTP - RC3
- Automatically disable flow control on ports using QOS bandwidth limits to prevent packet locks - RC3
- Added restart timer to DC power supply to help in very cold environments with cold starts - RC3
- Added log message when time is set by NTP after boot is finished - RC3
- Added logging when STP selects new root port - RC3
- Added POE startup delay option on Power tab - RC3
- Added root path cost on STP tab - RC3
- Added portDuplex SNMP stat from CISCO-STACK-MIB - RC3
- Added ifAdminStatus to SNMP stats - RC3
- Added support for new WS-26 models - RC6
- Added Double Tagged to VLAN configuration - RC6
- Added IP Protocol to QoS rules - RC11
- Added CIDR notation in QoS Source IP rules - RC11
- Added option to log web and ssh logins - RC11
- Added LLDP-MIB and CISCO-CDP-MIB to SNMP - RC 14
- Added option to change MAC aging time - RC14
- Added "Disable Power" action to watchdog - RC16

KNOWN ISSUES
- Some language templates need help - please contact us to help

RC3 Released 1/3/2017
RC4 Released 1/3/2017
RC6 Released 1/26/2017
RC7 Released 1/27/2017
RC8 Released 2/7/2017
RC9 Released 2/16/2017
RC10 Released 2/20/2017
RC11 Released 2/22/2017
RC14 Released 3/7/2017
RC16 Released 4/4/2017
RC18 Released 4/7/2017

[KBrownConsulting]

Trivial issue: The Copyright info at the bottom of the web GUI still says: "Copyright 2014-2016 Netonix"

[Dave]

thanks....

[ftxsteve]

You've still got a bug in VLAN operation on the latest software.
I have port 2 and 3 set up identically on the 6-port switch. On my OLT, port 5 sends VLANs 102 and 152. Port 6 sends port 201. When 5 connects to 2, only VLANs 102 and 152 work. OLT port 6 is connected to Netonix port 3. VLAN201 does not work in this scenario. When I swap the cables for the ports (2 to 3 and 3 to 2), only VLAN 201 works.

All I am doing is a simple cable swap at the Netonix.

I've tried this same test with ports 2 and 6 on the Netonix with the same result.

No changes were made in the OLT or the upstream router. The only thing that was done was reverse the cables at the mini-6.

[sirhc]

Why do you have Ports 2 and 3 set to pass all VLAN IDs with "Port Trunk/Allowed VLANs"?

Also are you giving it time for the MAC tables to clear and update?

I am pretty sure this is NOT a big as this would be a MAJOR VLAN bug causing all sorts of people problems including me.

You do understand that every switch port has a difference MAC address and is another Layer 2 hop in the chain.

[Dawizman]

Any release notes on the rc19+ firmware? Just wondering what changes have been made other than compatibility for the WS-26 switches.

Thanks.