Firmware Version: 1.4.7
Model: WS-26-400-AC
Board Rev: B
Has happened once before on older firmware, but I did not have remote serial access. This time I did and was able to get it to start again with #killall switch. Nothing obvious in the log. Did not have to reboot the switch... What info do you need to ID why it stopped forwarding?
Symptoms was that no traffic was passing. Looking at MAC table only showed about 20 entries, and it should have been 250 or so. Did killall switch and got the following output.
admin@SodaMain:/www# killall switch
killall: can't kill pid 832: No such process
killall: can't kill pid 833: No such process
admin@SodaMain:/www# Terminated
Logged back in and MAC table started to grow. Is passing traffic now.
/thanks
/rh
Switch stops forwarding traffic..
-
holbor - Member
- Posts: 4
- Joined: Wed Jan 13, 2016 5:46 pm
- Location: Scenic Rogue River Valley, OR
- Has thanked: 0 time
- Been thanked: 0 time
-
sirhc - Employee
- Posts: 7416
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: Switch stops forwarding traffic..
Sounds like maybe a Flow Control packet lock.
AirFIBER and AC radios to my knowledge still have a flow control bug where they send endless Pause Frames until the switch buffers fill up and then the switch refuses to accept anymore packets.
Maybe explain what is plugged into each port.
Post up Your config Tabs
AirFIBER and AC radios to my knowledge still have a flow control bug where they send endless Pause Frames until the switch buffers fill up and then the switch refuses to accept anymore packets.
Maybe explain what is plugged into each port.
Post up Your config Tabs
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
- Julian
Re: Switch stops forwarding traffic..
what this guy said ^.
also, it's important to use the latest RC on the 26-port switches - there were some bugs with 1.4.7 final, which you may be experiencing.
also, it's important to use the latest RC on the 26-port switches - there were some bugs with 1.4.7 final, which you may be experiencing.
-
holbor - Member
- Posts: 4
- Joined: Wed Jan 13, 2016 5:46 pm
- Location: Scenic Rogue River Valley, OR
- Has thanked: 0 time
- Been thanked: 0 time
Re: Switch stops forwarding traffic..
Just did it again... Same process to reload switch, all comes back.
Switch has:
2 Rocket M5 Titanium
4 UVC-G3 Cameras
2 Rocket M5
2 Rocket 5AC
3 Rocket Prism5AC
1 EdgeRouter Pro
1 Tycon Envronmental Monitor
4 Vlans
No LAGs
No STP
The 3 Prism's and one camera are new in the last month. Everything else been in for a year. Any workaround for the pause frame issue... and how can I tell?
/thanks
/rh
Switch has:
2 Rocket M5 Titanium
4 UVC-G3 Cameras
2 Rocket M5
2 Rocket 5AC
3 Rocket Prism5AC
1 EdgeRouter Pro
1 Tycon Envronmental Monitor
4 Vlans
No LAGs
No STP
The 3 Prism's and one camera are new in the last month. Everything else been in for a year. Any workaround for the pause frame issue... and how can I tell?
/thanks
/rh
-
sirhc - Employee
- Posts: 7416
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: Switch stops forwarding traffic..
Disable Flow Control on all ports first to see if this is what is going on.
If is a know issue with UBNT airFIBER and AC radios.
If is a know issue with UBNT airFIBER and AC radios.
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
holbor - Member
- Posts: 4
- Joined: Wed Jan 13, 2016 5:46 pm
- Location: Scenic Rogue River Valley, OR
- Has thanked: 0 time
- Been thanked: 0 time
Re: Switch stops forwarding traffic..
Well that went poorly :-(... should have thought about it more... but..
Dutifully went through and set flow control to NONE on all ports... even the uplink on the SFP port... (bad idea).. Caused the link to go down.. and NOT come back. 60 seconds went by... nothing. Serial into switch, link down. reset config to BOTH on port, nothing, killall switch, nothing.. reload cold.. nothing.. dropping to the CLI and doing a reboot... got it back..
However. I have managed to disable flow control on all AC sectors, so we'll see. Last time was 5 days between drops.
/rh
Dutifully went through and set flow control to NONE on all ports... even the uplink on the SFP port... (bad idea).. Caused the link to go down.. and NOT come back. 60 seconds went by... nothing. Serial into switch, link down. reset config to BOTH on port, nothing, killall switch, nothing.. reload cold.. nothing.. dropping to the CLI and doing a reboot... got it back..
However. I have managed to disable flow control on all AC sectors, so we'll see. Last time was 5 days between drops.
/rh
-
sirhc - Employee
- Posts: 7416
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: Switch stops forwarding traffic..
Please post up screen grabs of all you Config TABs
Do you have port's SPeed/Duplex set to Auto? <== SOUNDS LIKE NO
Turning OFF FC should not cause this.
Do you have port's SPeed/Duplex set to Auto? <== SOUNDS LIKE NO
Turning OFF FC should not cause this.
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
holbor - Member
- Posts: 4
- Joined: Wed Jan 13, 2016 5:46 pm
- Location: Scenic Rogue River Valley, OR
- Has thanked: 0 time
- Been thanked: 0 time
Re: Switch stops forwarding traffic..
Duplex is Auto.. Images attached. Everything else is pretty much defaults.
8 posts
Page 1 of 1
Who is online
Users browsing this forum: No registered users and 54 guests