v1.5.0rc3 and newer Bug Reports and Comments.

[mrprimo]

I upgraded a six units (all WS-12-250-DC) and the snmp has stopped working on all of them - I upgraded from 1.5.0rc3 to rc5.

[IntL-Daniel]

We have reported unexpected reboots of our WS12-250-AC. Could this fix:
Improved the units ability to deal with network loops while loop protection, flow control, and STP are disabled to not cause unit to reboot
- RC5


be related to our issue while we have loop protection (because of false detections) and STP (because of incorrect deal with other switches) disabled? We use flow control and pause frame storm protection only.

Thanks.

[sirhc]

We have reported unexpected reboots of our WS12-250-AC. Could this fix:
Improved the units ability to deal with network loops while loop protection, flow control, and STP are disabled to not cause unit to reboot
- RC5


be related to our issue while we have loop protection (because of false detections) and STP (because of incorrect deal with other switches) disabled? We use flow control and pause frame storm protection only.

Thanks.

Depends on what your reboot is caused by, if your reboots are related to a loop occurrence somewhere in your network yes.

When you encounter a problem you should always try the latest firmware version.
If that does not help swap the unit out with a spare and if the problem goes away you know it is related to the unit then RMA it.
If after upgrading to the latest firmware and then swapping the unit out your problem still exists you should start a new thread explaining your problem in detail with screen grabs of all TABs with changes from default and go from there.

[sirhc]

Yes it is confirmed that we broke SNMP in v1.5.0rc5

We will release v1.5.0rc6 tonight with that fixed and 2 features people requested.

We then want to FINALIZE v1.5.0 and will then start on v1.5.1rcX

[Rynet]

Around what time will RC6 be out? Have a Solar Site that needs SNMP. Upgraded to get CPU usage down so that the batteries dont drain as fast.

[sirhc]

Was hoping yesterday so probably today?

[sirhc]

I REALLY NEED FEEDBACK FAST - NEED TO FINALIZE MONDAY.
PLEASE GUYS, TRY IT OUT GET BACK TO US!

FIXED/CHANGED
- Fixed I2C service to deal with errors better to prevent reboots with WS-12-250-DC and WS-26-500-DC - RC2 & RC3
Note: The attempt to fix I2C in RC2 was a failure and caused worse issues.
It was rushed out too fast with not enough testing.
If you downloaded v1.5.0rc2 DELETE IT AND NEVER USE IT AGAIN
We spent almost a week testing the I2C in RC3 and feel we got it right this time.

- Fixed sending CDP frames tagged with VID 1 if the management VLAN is not VID 1 - RC1
- Fixed SNMP walk failing if VLANs are not in numerical order - RC1
- Fixed using hash mark in SMTP password - RC1
- Fixed using hash mark in RADIUS password - RC1
- Fixed issues with Loop Protection on SFP ports - RC1
- Fixed intermittent telemetry error on Device/Status TAB mostly seen with WS-26-500-DC - RC1
- Fixed power TAB shutdown time set to 12 AM would turn off poe on that port - RC4
- Fixed ST/RSTP bridge priority change would not update properly - RC4
- Fixed cli on WS-8-150-DC model's allowing one to set the power restart/shutoff from cli - RC5
- Fixed scheduled portbounce to no longer trigger unexpected link status change email - RC5
- Extended length for URL resource for SMTP recipient address - RC5
- Fixed SNMP broken in v1.5.0rc5 due to a build mistake - RC6
- Fixed SNMP handling longer firmware version - RC6

ENHANCEMENTS
- Optimized code to reduce CPU utilization especially needed for the WS-26-500-DC - RC1 <= CRITICAL
- Changed watchdog waits + Interval seconds before checking again after watchdog is triggered - RC1
- Added log entry to report if the switch rebooted due to watchdog timer - RC1
- Added lldpRemPortId, lldpRemPortIdSubtype, and lldpRemPortDesc to LLDP-MIB - RC1
- Added cdpCacheDevicePort to CISCO-CDP-MIB - RC1
- Added popover for POE enabled ports on 'Watts' column to show power usage on each pair for VH ports - RC1
- Added root bridge id to STP log message - RC1
- Added Low Voltage notification for DC model's to contain the threshold and the present value in the log/email - RC5
- SNMP Contact and Location character limit increased from 26 to 255 characters - RC4
- Improved ability to deal with loops while loop protection, flow control, and STP disabled to not reboot - RC5
- Added checkbox to SYSLOG Configuration called "Log Name" which appends the switch name to messages - RC6
- Added Calling-Station-Id to RADIUS attributes to allow freeradius to log ip address of client - RC6

KNOWN ISSUES
- WEB UI issues when not at 100% Zoom on browser especially on VLAN TAB
- Some language templates need help - please private message Eric Stern to help
- IGMP snooping over VLANS, MSTP, and ERPS are still being developed

RC1 Released 3/19/2018
RC2 Released 3/22/2018
RC3 Released 4/3/2018
RC4 Released 4/30/2018
RC5 Released 5/25/2018 - BROKE SNMP Confirmed 5/31/2018
RC6 Released 6/2/2018

[mrprimo]

snmp is working on them again

[IntL-Daniel]

One note - we have year 2018...your copyright says up to 2017.