v1.5.2rcX Bug reports and comments

[Stephen]

Confirmed, on firefox specifically clicking the data refresh on the discovery tab causes the web page to reset. Should be fixed on the next release.

[Stephen]

FIXED/CHANGED
- Fixed voltage input calibration for the WS-8-150-DC
- Fixed services running on IPv6
- Fixed being able to bypass console login by hitting CTRL-C
- Fixed MSTP setting instance forwarding state
- Fixed UI on ERPS tab to prevent footer from from being mangled
- Fixed ERPS MEPs issue that triggered a Signal Fail on a ring when port not in the ring is disconnected/disabled
- Fixed ERPS issue that prevented access to Management VLAN when added to the protected VLAN list
- Fixed ERPS protected VLANs would not forward packets outside of the ring
- Fixed SNMP (Broken in v1.5.1rc3)
- Fixed Access Controls for a confirmed security vulnerability -(for more details check this thread: viewtopic.php?f=12&t=4103 )
- Fixed UI bug in Access Control List
- Fixed DHCP failure when switch has a static ip assigned to a vlan
- Increased time buffer for warning voltage email trigger
- MAC Table search works using colons and dashes
- update for new fans
- fixes for PoE sensor balloon performance issue and data display
- fix for LACP LAG breaking during config changes

ENHANCEMENTS

KNOWN ISSUES
- WEB UI issues when not at 100% Zoom on browser especially on VLAN TAB
- Some language templates need help - please private message Eric Stern to help
- IGMP snooping over VLANS, MSTP, and ERPS are still being developed
- Discovery tab can experience performance issue's on a large layer 2 segment, a re-work on this sub-system is in progress

Released 1/28/2019

FIXED/CHANGED
- Fixed IGMP snooping - RC1
- Fixed IGMP snooping with multiple VLANs - RC2
- Fixed disabling IGMP querier - RC2
- Fixed IGMP handling tagged frames - RC3
- Fixed STP/LAG issue, this fix prevents switches from being locked out when access is through a lag - RC4
- Fixed STP/LAG issue, significant performance improvement when making configuration changes - RC4
- Updated Copyright - RC4


ENHANCEMENTS
- Added IGMP Snooping monitoring in the web UI (Device -> IGMP Snooping). Aready in CLI ("show igmp") - RC1
- Port Selection De-selection now functions with the ports graphic at top of switch web UI - RC3
- Legacy/New fan test is now asynchronous, reboots/upgrades are now much faster - RC4
- Added button to fan status to allow user to initiate an asynchronous fan test - RC4
- Discovery tab now allows for individual to select which protocol is being searched for instead of all simultaneously - RC4
- Discovery tab configuration is more intuitive. - RC5
- Fan test now records results and only needs to re-run if manual test is activated, firmware update occurs, or default occurs - RC5

KNOWN ISSUES
- WEB UI issues when not at 100% Zoom on browser especially on VLAN TAB
- Some language templates need help - please private message Eric Stern to help
- Discovery tab can experience performance issue's on a large layer 2 segment, a re-work on this sub-system is in progress

RC5 - Released 3/17/2019
RC4 - Released 3/1/2019
RC3 - Released 2/8/2019
RC2 - Released 2/7/2019
RC1 - Released 2/6/2019

[sakita]

"- Fan test now records results and only needs to re-run if manual test is activated, firmware update occurs, or default occurs - RC5"

Where does it record the fan test? I didn't see anything in the log... it would be nice to see that it passed the test on startup as well as if it passed on a manual test along with which mode...

Oh, and I had to figure out what 'more intuitive' meant for the discovery tab config: basically Discovery Tab cannot be enabled unless at least one of the protocols is enabled: makes sense!

[Stephen]

If you go to the Device Status Tab and scroll to the bottom there is a panel that shows the fan status.
The point of the fan test is to determine what type of fans are installed. Because of a manufacturer changing specs on the fans without telling us we needed to be able to determine which version of fan is in the switch to adjust it's settings and allow it to function appropriately. If the test passed you will see there what the fan mode is. If it failed the fan's will have a message 'ERR' next to them.

[Stephen]

For awhile there have been issue's with Discovery on larger layer 2 segments, changes in this build have been tested for several weeks with both emulated and real discoverable devices and we have seen a significant performance improvement. Also there was a memory leak reported that we believe we have finally tracked down. We are wanting to finalize 1.5.2 soon so please let us know if you notice any steady increases in memory when using discovery or if there are any noticeable performance differences for a large number of discoverable devices.

FIXED/CHANGED
- Fixed IGMP snooping - RC1
- Fixed IGMP snooping with multiple VLANs - RC2
- Fixed disabling IGMP querier - RC2
- Fixed IGMP handling tagged frames - RC3
- Fixed STP/LAG issue, this fix prevents switches from being locked out when access is through a lag - RC4
- Fixed STP/LAG issue, significant performance improvement when making configuration changes - RC4
- Updated Copyright - RC4
- Memory Leak found in Discovery process has been fixed (please report any more occurrences) - RC6
- Fan settings storage was not applying changes for new fans - RC6


ENHANCEMENTS
- Added IGMP Snooping monitoring in the web UI (Device -> IGMP Snooping). Aready in CLI ("show igmp") - RC1
- Port Selection De-selection now functions with the ports graphic at top of switch web UI - RC3
- Legacy/New fan test is now asynchronous, reboots/upgrades are now much faster - RC4
- Added button to fan status to allow user to initiate an asynchronous fan test - RC4
- Discovery tab now allows for individual to select which protocol is being searched for instead of all simultaneously - RC4
- Discovery tab configuration is more intuitive. - RC5
- Fan test now records results and only needs to re-run if manual test is activated, firmware update occurs, or default occurs - RC5
- Rebuild Discovery process and now runs more efficiently on larger layer 2 segments - RC6

KNOWN ISSUES
- WEB UI issues when not at 100% Zoom on browser especially on VLAN TAB
- Some language templates need help - please private message Eric Stern to help
- Discovery tab can experience performance issue's on a large layer 2 segment, a re-work on this sub-system is in progress

RC6 - Released 3/22/2019
RC5 - Released 3/17/2019
RC4 - Released 3/1/2019
RC3 - Released 2/8/2019
RC2 - Released 2/7/2019
RC1 - Released 2/6/2019