v1.5.5 Bug Reports and Comments

[cwachs]

Took 20 switches from 1.5.2 to 1.5.5 last night. Am seeing some issues. On 5 of the switches, SNMP would not work after reboot. Turning SNMP off and then on again woke it up.

On all switches, watchdog options are different and the first two are blank in the drop down. Can't tell what they say:

Screen Shot 2019-11-01 at 4.19.26 PM.png (32.42 KiB) Viewed 9197 times

If I want to bounce the port power, what option do I select?

One of my WS-12-DC units, I am seeing lots of STP port flapping.

[bipbaep]

Seeing same issues as cwachs

[ogreland]

After upgrade to 1.5.5 fan stopped operate. CPU and PHY is about 75 C. Run Fan Test is ok - 10k rpm.

[sirhc]

After upgrade to 1.5.5 fan stopped operate. CPU and PHY is about 75 C. Run Fan Test is ok - 10k rpm.

Maybe because you upgraded from an much older firmware and we had changed the temps fan operate at.

Fan does not start until board temp is 45C

Post up a screen grab of your DEVICE/STATUS TAB

[ogreland]

After upgrade to 1.5.5 fan stopped operate. CPU and PHY is about 75 C. Run Fan Test is ok - 10k rpm.

Maybe because you upgraded from an much older firmware and we had changed the temps fan operate at.

Fan does not start until board temp is 45C

Post up a screen grab of your DEVICE/STATUS TAB

Yes, i have upgraded from old version.
Below is a stats.

[ogreland]

Temperatures:

[sirhc]

Looks FINE.

When your board temp reaches 45C the fan will kick on.

The CPU and PHY are rated to run at 125C

Discussed many many times already, there is a search feature on the forums to find the info you need.

https://forum.netonix.com/viewtopic.php?f=6&t=4918&p=27922&hilit=45C#p27922

https://forum.netonix.com/viewtopic.php?f=6&t=4918&p=27929&hilit=45C#p27929

https://forum.netonix.com/viewtopic.php?f=17&t=5528&p=29708&hilit=45C#p29708

https://forum.netonix.com/viewtopic.php?f=6&t=4983&p=28200&hilit=45C#p28200

[ogreland]

Many thanks!

[lligetfa]

Looks FINE.

When your board temp reaches 45C the fan will kick on.

The CPU and PHY are rated to run at 125C

Discussed many many times already...

A bit of a digression but if the colour would stay green for longer and not do a Chicken Little impression, then folks might not panic as often.

[banderson]

Adding to 'restarting vtss_appl' posts, here is my log and will PM backup. Box was 1.4.7, as were 2 others (other 2 are fine, just issues with this one -- the Throughput graphs freeze, but update with manual browser refresh).




Dec 31 17:00:10 system: Setting MAC address from flash configuration: EC:13:B2:A1:4C:66
Dec 31 17:00:12 system: starting ntpclient
Dec 31 17:00:13 admin: adding lan (eth0.58) to firewall zone lan
Dec 31 17:00:13 dropbear[649]: Running in background
Dec 31 17:00:14 netonix: 1.5.5 on WS-12-DC
Dec 31 17:00:16 UI: web config OK
Dec 31 17:00:27 switch[799]: temp sensor version 3
Dec 31 17:00:28 switch[800]: Detected warm boot
Dec 31 17:00:33 system: starting ntpclient
Nov 12 16:08:08 monitor: restarting vtss_appl
Nov 12 16:08:09 system: time set by NTP server
Nov 12 16:08:21 monitor: restarting vtss_appl
Nov 12 16:08:35 monitor: restarting vtss_appl
Nov 12 16:08:48 monitor: restarting vtss_appl
Nov 12 16:09:02 monitor: restarting vtss_appl
Nov 12 16:09:15 monitor: restarting vtss_appl
Nov 12 16:09:28 monitor: restarting vtss_appl
Nov 12 16:09:42 monitor: restarting vtss_appl
Nov 12 16:09:56 monitor: restarting vtss_appl
.... and so on


Can't PM the backup, says extension not allowed (tried changing to others -- nothing seems to attach ;(

-- ^^ got attached by .zip (per suggestion) .. thx