v1.3.3 FINAL bug reports and comments

[gerardor884]

I have set up these settings on the watchdog, please advise if the setting are not properly set up. Thank you

[sirhc]

1) What version of the firmware are you running? There were recent fixes for watchdog. ***see firmware release notes***

2) Please explain what happens? Either nothing or it keeps rebooting your radios?

Please post the VLAN Tab and Device/Config Tab

[gerardor884]

1) What version of the firmware are you running? There were recent fixes for watchdog. ***see firmware release notes***
I have the firmware version 1.3.2

2) Please explain what happens? Either nothing or it keeps rebooting your radios?
it does nothing, it does not responds

Please post the VLAN Tab and Device/Config Tab
I am not using VLAN, VLAN is not enable

[sirhc]

1) What version of the firmware are you running? There were recent fixes for watchdog. ***see firmware release notes***
I have the firmware version 1.3.2

2) Please explain what happens? Either nothing or it keeps rebooting your radios?
it does nothing, it does not responds

Please post the VLAN Tab and Device/Config Tab
I am not using VLAN, VLAN is not enable

What do you mean it does not respond?
It should not respond unless the pings fail 3 consecutive pings in a row and then disable the port POE for 5 seconds rebooting it the device and then send you a an SMPT message provided you have SMTP setup correctly.
I am running a test now to confirm it works, I know I tested this a few weeks ago.

This shows in the log that a ping watchdog was enabled. I have it pinging an address that nothing is at so it will fail.

Sep 8 17:56:18 UI: Configuration changed by 192.168.1.176
Sep 8 17:56:18 UI: PingWatchdog 1 Enable: changed from 'Disabled' to 'Enabled'
Sep 8 17:56:20 pinger: starting up with 1 ping watchdogs and 0 scheduled port bounces

Sure enough it did work and rebooted my camera

Sep 8 17:57:59 pinger: Failure pinging 192.168.1.15, powering off port 10 for 10 seconds
Sep 8 17:57:59 pinger: Cannot notify, SMTP is not enabled

CLICK IMAGE BELOW TO VIEW FULL SIZE

watchdog.jpg (399.62 KiB) Viewed 9145 times

[sirhc]

Please post comments and reports bugs with v1.3.3 FINAL in this thread

NOTE: We had some enhancements for the SFP ports but we decided to remove them as they were still buggy but will put them back in the v1.3.4 firmware so for now SFP ports are handled the same as v1.3.2. So if you needed the SFP enhancements to make your SFP module work please wait until we release v1.3.4rc1 which should be in a couple days.

FIXES
- Fixed VLAN configuration
- Fixed slowness with configurations with hundreds of VLANs
- Fixed slowness with MAC Table with thousands of MACs
- Fixed problem with MAC Table on SFP ports on 12 port models
- Fixed POE power being turned off when port is disabled or not in a VLAN if POE Smart is enabled
- Fixed IP address lookup for MAC Table
- Fixed support for WS-12-DC
- Fixed some log messages
- Fixed problem with Auto backup TFTP URLs containing a path
- Changed input voltage check to only happen on dumb DC models

ENHANCEMENTS
- Added reboot after resetting to defaults in CLI
- Added timed shutdown periods for PoE on DC models
- Improved VLAN tab UI
- Added Flow Control indicator to Link column on Status tab
- Added email notifications for LACP port status changes
- Changed RSTP to be enabled by default

KNOWN ISSUES
- Ubiquiti Discovery Protocol is still flaky
- IPERF is a work in progress

[keefe007]

What was fixed with VLAN configuration?

[sirhc]

What was fixed with VLAN configuration?

Eric is off line but I believe it was to do with the Management VLAN

Here was one example where it solved an issue:
viewtopic.php?f=17&t=930&p=7712&hilit=v1.3.3rc5#p7697

[anvilcom]

After lab'ing our WS-12-250-AC we finally deployed it. I hadn't tested the email feature since 1.2.4 or so. Now testing shows that ssmtp actually uses the mail host name as the client host name while EHLO 'ing. Our server will drop the connection as it detects this as a forged host name - and rightly so.

I checked both /etc/ssmtp/ssmtp.conf and /jffs/etc/ssmtp/ssmtp.conf. They both have the the same value for the two different variables:

Code: Select all

mailhub=[mail.ourdomain.com]:25
hostname=mail.ourdomain.com

AFAIK, hostname should be the actual host name assigned to the switch, not the name of the mail server.

We are running version 1.3.3

Maybe this has already been addressed, but I thought I'd report it anyway.

[designweb]

i have not seen one mac address since putting 1.3.3 on ten switches so far, all worked fine on previous versions

[sirhc]

i have not seen one mac address since putting 1.3.3 on ten switches so far, all worked fine on previous versions

I am not sure I follow what your saying here?