I've run into this odd problem, and I hope that someone can help me figure out what's going on. I've tested with both WS-6-mini-AC's and a WS-8DC, using the latest firmware and even some of the older firmware loads and the problem persists.
If I have a unit supplying 48VH to a WS-6-mini, but I have the port disabled (don't want ethernet), on a reboot it will fail to power correctly the WS-6-mini and it never boots up. If I then enable the port, it will begin to power the WS-6-mini correctly, at which point I can go ahead and disable the port again and everything works fine.
This happens regardless of if I have POE-smart enabled for that port or not.
I've setup a bunch of units on the test bench and have been able to replicate the problem consistently.
Is this a bug or am I doing something wrong? Thanks
Netonix 48VH port doesn't power on after reboot
-
zhall - Member
- Posts: 19
- Joined: Mon Dec 01, 2014 2:01 pm
- Has thanked: 0 time
- Been thanked: 0 time
-
sirhc - Employee
- Posts: 7416
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: Netonix 48VH port doesn't power on after reboot
This I thought was fixed in v1.3.3??
Are you sure you are running v1.3.3 on the switch that powers the MINI?
Are you sure you are running v1.3.3 on the switch that powers the MINI?
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
zhall - Member
- Posts: 19
- Joined: Mon Dec 01, 2014 2:01 pm
- Has thanked: 0 time
- Been thanked: 0 time
Re: Netonix 48VH port doesn't power on after reboot
Yah, both netonix's we tested it with were running the latest 1.3.3
Firmware Version 1.3.3
Firmware Version 1.3.3
-
sirhc - Employee
- Posts: 7416
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: Netonix 48VH port doesn't power on after reboot
I have not tested this but I will assume what you say is correct and will make sure it gets addressed in v1.3.5 which "should" be coming out soon?
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
zhall - Member
- Posts: 19
- Joined: Mon Dec 01, 2014 2:01 pm
- Has thanked: 0 time
- Been thanked: 0 time
Re: Netonix 48VH port doesn't power on after reboot
Very good! Quite so. Marvelous product.
-
adairw - Associate
- Posts: 465
- Joined: Wed Nov 05, 2014 11:47 pm
- Location: Amarillo, TX
- Has thanked: 98 times
- Been thanked: 132 times
Re: Netonix 48VH port doesn't power on after reboot
instead of disabling the port, set it in it's own vlan. that way it's up, but can't talk to anything. just a thought.
6 posts
Page 1 of 1
Who is online
Users browsing this forum: No registered users and 36 guests