i2c error:
-
lligetfa - Associate
- Posts: 1191
- Joined: Sun Aug 03, 2014 12:12 pm
- Location: Fort Frances Ont. Canada
- Has thanked: 307 times
- Been thanked: 381 times
Re: i2c error:
Did you plug an SFP into the switch? An incompatible SFP could cause contention on the i2c buss.
-
sirhc - Employee
- Posts: 7416
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: i2c error:
sww wrote:I just fired up another one out of the batch and it's working normally. It's got 1.3.4 on it. Should I try to update it and see what happens? Should I be able to go from 1.3.4 straight to 1.3.7rc4? Or should I be upgrade in steps?
Yes, I would use v1.3.7rc4
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
sww - Member
- Posts: 43
- Joined: Tue Aug 25, 2015 12:41 pm
- Location: Roswell, NM
- Has thanked: 0 time
- Been thanked: 10 times
Re: i2c error:
We are not using SFP with any of these, plus the last one in question is an 8 port that does not have them. The 2 that I think we damaged should be coming back today and tomorrow and I'll get with you on sending them in, I'd like to send this 3rd one in for you to look at as well. How do I setup an RMA?
-
sirhc - Employee
- Posts: 7416
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: i2c error:
sww wrote:We are not using SFP with any of these, plus the last one in question is an 8 port that does not have them. The 2 that I think we damaged should be coming back today and tomorrow and I'll get with you on sending them in, I'd like to send this 3rd one in for you to look at as well. How do I setup an RMA?
Email me at Chris@netonix.com requesting an RMA
State the units with their MAC address
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
sww - Member
- Posts: 43
- Joined: Tue Aug 25, 2015 12:41 pm
- Location: Roswell, NM
- Has thanked: 0 time
- Been thanked: 10 times
Re: i2c error:
1.3.8 seems to have resolved this issue for the time being. I had 2 units in the field that were still doing this after power cycles and various previous firmware upgrades. We upgraded them to 1.3.8 today and they are working normally again! Did you guys change anything or just a happy coincidence?
-
sirhc - Employee
- Posts: 7416
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: i2c error:
sww wrote:Did you guys change anything or just a happy coincidence?
There are these new fangled things called "Release Note", we put them in the post and thread where you download the firmware.
v1.3.8 wrote:FIXES
- Select all ports and add POE did not work correctly
- Port 1 Enables itself on reboot if disabled
- UI formatting Bugs
- Changed PoE Smart to now only check for "cross-shorts"
- Change voltage calculations to use 1 decimal point of precision
- Fan failure detection changes
- Better I2C error handling, primarily helps DC switches but better for all
- Fixes for DC switches Power Tab conditions
ENHANCEMENTS
- Add configurable config save timeout
KNOWN ISSUES
- Ubiquiti Discovery Protocol Still Broken
- large flat networks MAC table requiring too much CPU time
- IPERF is still a work in progress
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
-
sww - Member
- Posts: 43
- Joined: Tue Aug 25, 2015 12:41 pm
- Location: Roswell, NM
- Has thanked: 0 time
- Been thanked: 10 times
Re: i2c error:
lol I deserve that I guess. It's kinda like the Apple Agreement button from Southpark, nobody reads that stuff, but we will probably regret it sooner or later lol.
-
sirhc - Employee
- Posts: 7416
- Joined: Tue Apr 08, 2014 3:48 pm
- Location: Lancaster, PA
- Has thanked: 1608 times
- Been thanked: 1325 times
Re: i2c error:
sww wrote:lol I deserve that I guess. It's kinda like the Apple Agreement button from Southpark, nobody reads that stuff, but we will probably regret it sooner or later lol.
I absolutely LOVE that episode!
Support is handled on the Forums not in Emails and PMs.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Before you ask a question use the Search function to see it has been answered before.
To do an Advanced Search click the magnifying glass in the Search Box.
To upload pictures click the Upload attachment link below the BLUE SUBMIT BUTTON.
Who is online
Users browsing this forum: Bing [Bot], Google [Bot] and 50 guests